1
Voltage Gate
PASSDevice output type must match generator output.
120V required -> 120V/240V available
Yes, the Anker SOLIX F3800 can run a Circular Saw (Corded)
Yes - Anker SOLIX F3800 has enough running and surge power for the Circular Saw (Corded). Target ~2070W running / 6210W surge; the generator provides 6000W / 9000W.
Power Margin Analysis
6000W / 9000W Capacity Running 3930W headroom
2070W required
Surge 2790W headroom
6210W required
Decision Gate Waterfall
Same decision gates as the engine: voltage, running, surge. Runtime is shown as operational context.
2
Running Gate
PASSContinuous draw with safety buffer applied.
2,070W required -> 6,000W available (3,930W headroom)
Required 2,070W required
Available 6,000W
3
Surge Gate
PASSStartup peak with safety buffer applied.
6,210W required -> 9,000W available (2,790W headroom)
Required 6,210W required
Available 9,000W
4
Runtime Insight
INFORuntime context only. It does not change the electrical compatibility verdict.
Continuous estimate: 1.5h
Device profile reference: up to 1h per day.
Power bars show required versus available output for each gate.
View full compatibility reportDecision Snapshot
Quick compatibility, required headroom, and model-specific context at a glance.
⚡
6000W
Running Power
🔋
3840Wh
Capacity
⏱️
~1.5h
Est. Runtime
☀️
2400W
Solar Input
Quick Compatibility Check
- 1 Running headroom: target 2070W; generator provides 6000W.
- 2 Surge headroom: target 6210W; generator provides 9000W.
- 3 Tip: leave headroom for startup spikes and warm conditions.
Model-Specific Results
3 of 3 models are SAFE or TIGHT. Most demanding model: DeWalt DWE575 (7-1/4", 15A, Lightweight) (5,400W surge).
| Model | Running | Surge | Verdict | Runtime | Source |
|---|---|---|---|---|---|
| DeWalt DWE575 (7-1/4", 15A, Lightweight) | 1,800W | 5,400W | Safe | ~1.5h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1800W from OEM nameplate (15A × 120V). **Estimated startup surge:** 5400W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Universal motor, 5200 RPM no-load, 7-1/4" blade, 8.8 lbs. Field note: The DWE575 is the best-selling corded circular saw in the US. At 8.8 lbs it's the lightest 15A saw available, making it popular for overhead and extended jobsite use. The 5400W estimated surge means most power stations under 3000W surge capacity will struggle to start this saw under load. Can a portable power station run the DeWalt DWE575? Only if your power source can supply at least 1800W continuous and approximately 5400W surge at 120V. The motor startup surge is the main challenge — a 2000W station with only 3000W surge may trip on startup. | |||||
| Makita 5007MG (7-1/4", 15A, Magnesium) | 1,800W | 5,400W | Safe | ~1.5h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1800W from OEM nameplate (15A × 120V). **Estimated startup surge:** 5400W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Universal motor, 5800 RPM no-load, 7-1/4" blade, magnesium construction. Field note: The 5007MG's magnesium housing makes it durable and well-balanced for professional use. Its 5800 RPM is the highest in this set. From a power station perspective, it's electrically identical to the DeWalt — same 15A draw, same estimated 5400W surge. Choose between them based on ergonomics and blade speed, not electrical compatibility. Is the Makita 5007MG harder to run on a power station than the DeWalt? No — both draw 15A (1800W) with an estimated 5400W startup surge. The Makita spins faster (5800 vs 5200 RPM) but that doesn't affect the electrical load. Any power source that runs one will run the other. | |||||
| Ryobi CSB125 (7-1/4", 13A, Budget) | 1,560W | 4,680W | Safe | ~1.7h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1560W from OEM nameplate (13A × 120V). **Estimated startup surge:** 4680W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Universal motor, 5000 RPM no-load, 7-1/4" blade. Field note: The CSB125 is the most power-station-friendly circular saw in this set. At 1560W running and 4680W estimated surge, it opens up compatibility with mid-range power stations (3000W+ surge) that cannot start a 15A saw. If you're buying a corded saw specifically for portable power use, the 13A rating is a real advantage. Why choose the Ryobi 13A over a 15A saw for portable power? The 13A Ryobi draws 1560W running and an estimated 4680W surge — 13% less than 15A saws. This difference can mean the difference between a power station starting the saw or tripping on overload. | |||||
How This Pairing Performs Across Our Database
This unit ranks #7 of 9 compatible generators for this device by buffered margin (Overkill class).
How Circular Saw (Corded) Performs Across 33 Tested Generators
9 of 33 generators are SAFE+TIGHT for Circular Saw (Corded).
9
Safe+Tight
Safe 7 (21%)
Tight 2 (6%)
Fail 24 (73%)
Power Comparison: Anker SOLIX F3800 vs Top Alternatives for Circular Saw (Corded)
Anker SOLIX F3800 Safe Overkill
Current unit
Running 6,000W
Surge 9,000W
Fit class uses buffered needs (running and surge) for this device.
Specs & Surge Analysis
⚡
Power Tools
Circular Saw (Corded)
Job Site Power
Select Your Model:
1800W
Running
5400W
Surge
120V
Required
True Surge™ Analysis
Safety Buffer: +15% Running Power Usage 35% Utilization
2070W required 6000W Capacity
3930W headroom
Surge/Startup Peak 69% Utilization
6210W required 9000W Capacity
2790W headroom
Voltage Match 120V ↔ 120V/240V ✓
⚠️
Before You Buy: Connection Check
Amperage check
This load may exceed a standard 15A outlet. Verify your station has a higher-amperage outlet (20A/30A) before purchase.
Compare Similar Units
Free Tools
Station Tools
Generator Insights
The 9000W surge rating can handle typical compressor-based appliances like central air conditioners, well pumps, and refrigerators during startup. This capacity can support multiple simultaneous high-draw devices once running loads stabilize. Expect reliable operation for tools, HVAC systems, and other inductive loads that demand short-duration power spikes.
This unit employs LFP chemistry with a 3840Wh capacity, designed for stable discharge under high-demand conditions. The architecture supports both sustained and transient loads within rated limits. Source: Anker SOLIX F3800 User Manual v1.1 (Specifications) (OEM documentation).
Extend Runtime with Solar
Keep your Circular Saw (Corded) running with solar • MPPT: 11– 60V • Max: 2400W
Official Anker
100W Panel
1 Hour Sun =
+0h per sun hour
MC4 -> XT60
Full in ~54.9h Adapter required: MC4 -> XT60.
Smart Value EcoFlow
400W Panel
1 Hour Sun =
+0.2h per sun hour
MC4 -> XT60
Full in ~13.7h Adapter required: MC4 -> XT60.
Smart Value EcoFlow
400W Panel
1 Hour Sun =
+0.2h per sun hour
MC4 -> XT60
Full in ~13.7h Adapter required: MC4 -> XT60.
Technical Analysis
Spec-Based • No GuaranteesTechnical Breakdown
Running range: 1560W (13A) to 1800W (15A) depending on motor rating. Estimated surge range: 4680W to 5400W at 3x running (motor-load multiplier — no circular saw manufacturer publishes starting watts). Voltage: 120V AC for all corded models.
Expected Behavior
Estimated runtime: ~1.5h. Circular saws draw near-maximum rated power during cutting and drop to near-zero between cuts. Unlike compressors or refrigerators, there is no continuous cycling — the load is entirely user-controlled. At 1 hour daily use, energy consumption ranges from 1560 to 1800 Wh depending on model.
Field Note
Startup surge is the primary compatibility bottleneck, not running watts. A circular saw motor must overcome blade inertia from standstill, creating a brief 3x inrush event. Blade binding in wood can also spike current above rated amps — size your power source for the surge rating, not the nameplate amps.
Frequently Asked Questions
Can the Anker SOLIX F3800 power a Circular Saw (Corded)?
Yes. The Anker SOLIX F3800 provides 6000W running / 9000W surge. The Circular Saw (Corded) needs 2070W / 6210W (including 15% buffer). That leaves 3930W of running headroom and 2790W of surge margin.
How long will the Anker SOLIX F3800 run a Circular Saw (Corded)?
Approximately 1.5 hours, based on the Circular Saw (Corded)'s 1800W draw and the Anker SOLIX F3800's 3840Wh capacity (70% usable after real-world losses).
What Else Can You Run?
With 1005W allocated to the Circular Saw (Corded), the Anker SOLIX F3800 still has ~1995W of margin. These devices could run simultaneously:
💡
LED Lamp
10W
🌀
Box Fan (Medium)
60W
📺
55' LED TV
80W
🔥
Space Heater (Eco)
750W
💻
MacBook Air/Pro
65W
🩺
CPAP (No Humidifier)
40W
Power Tip: To get the most out of your Anker SOLIX F3800, keep it in a well-ventilated area. Extreme temperatures can slightly reduce the efficiency of the LFP/NMC cells.
Compare all 33 generators for the Circular Saw (Corded)
Ranked by budget, runtime, and overall compatibility.
Technical Sourcing & Verification
ID: anker-solix-f3800-circular-saw-corded 🏛️ Device Data Source
Engineering Est. Safety Factor Applied
Derived from variant list (max of variants). Running worst case = DeWalt DWE575 / Makita 5007MG (1800W at 15A). Surge worst case = DeWalt DWE575 / Makita 5007MG (5400W). Surge estimated using 3x motor-load multiplier policy (no OEM starting watts published for any circular saw in this class).
⚡ Generator Specs Source
OEM Verified
Anker SOLIX F3800 User Manual v1.1 (Specifications)
Methodology informed by US Department of Energy (DOE) & EIA references where applicable.
Our methodology →
Compare these models
Similar-output alternatives you can compare side by side.