1
Voltage Gate
PASSDevice output type must match generator output.
120V required -> 120V available
Can the SOLIX C800 Plus Run a Gas Furnace Fan (Blower)? It Depends on Your Model
2 of 3 models are compatible with this generator.
Jump to model-specific results ↓Power Margin Analysis
1200W / 1600W Capacity Running Up to 268W headroom on lighter models; 17W short on demanding models
932W to 1217W required
Surge 81W to 1195W short by model
1681W to 2795W required
Decision Gate Waterfall
Same decision gates as the engine: voltage, running, surge. Runtime is shown as operational context.
2
Running Gate
PARTIALContinuous draw with safety buffer applied.
932W to 1,217W required -> 1,200W available (268W headroom on lighter models)
Required 932W to 1,217W required
Available 1,200W
3
Surge Gate
FAILStartup peak with safety buffer applied.
1,681W to 2,795W required -> 1,600W available (81W to 1,195W short)
Required 1,681W to 2,795W required
Available 1,600W
3b
With Soft-Start
PASSAlternative startup path with reduced inrush.
1,258W required -> 1,600W available (342W headroom)
Required 1,258W
Available 1,600W
4
Runtime Insight
INFORuntime context only. It does not change the electrical compatibility verdict.
Continuous estimate: 0.5h
Device profile reference: up to 8h per day.
Power bars show required versus available output for each gate.
View full compatibility reportDecision Snapshot
Quick compatibility, required headroom, and model-specific context at a glance.
⚡
1200W
Running Power
🔋
768Wh
Capacity
⏱️
~0.5h
Est. Runtime
☀️
300W
Solar Input
Quick Compatibility Check
- 1 2 of 3 models are compatible with the SOLIX C800 Plus.
- 2 Model requirements range from 810W to 1058W running watts.
- 3 See the model-specific results table for per-model verdicts.
Model-Specific Results
2 of 3 models are SAFE or TIGHT. Most demanding model: Goodman GMH8 0805B (80,000 BTU) (2,430W surge).
| Model | Running | Surge | Verdict | Runtime | Source |
|---|---|---|---|---|---|
| Carrier Infinity 59MN7A 080 (80,000 BTU) | 886W | 1,461W | Tight | ~0.6h | OEM Manual |
Show expert analysisTechnical: **Running load:** 886W (115V × 7.7A FLA, OEM rated). **Surge:** 1,461W (115V × 12.7A start amps, OEM rated). **Voltage:** 120V AC. The ECM variable speed blower ramps up electronically with a controlled startup — the 1,461W surge is brief and predictable. Field note: The Carrier Infinity is the most generator-friendly furnace blower in this comparison. The ECM variable speed motor keeps both running and surge watts low. Most power stations above 1,500W can handle this unit without issue. Can I run a Carrier Infinity furnace on a portable power station during a winter outage? Only if your power source can supply at least 886W continuous and 1,461W surge at 120V. The ECM variable speed blower has a controlled startup that most mid-size power stations can handle. | |||||
| Trane S8X1 B080 (80,000 BTU) | 1,058W | 1,587W | Tight | ~0.5h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1,058W (115V × 9.2A FLA, OEM rated). **Surge:** 1,587W estimated (1.5× for ECM constant torque motor — OEM start amps not published). **Voltage:** 120V AC. The 3/4 HP constant torque ECM blower draws more than the Carrier variable speed but still benefits from electronic startup control. Field note: The Trane S8X1 is a mid-range 80% AFUE furnace common in existing homes. The 9-speed ECM blower is more efficient than old PSC motors but draws more than premium variable speed models. A 2,000W power station provides adequate headroom. Can I keep my Trane furnace running on battery backup during a winter storm? Only if your power source can supply at least 1,058W continuous and 1,587W surge at 120V. The ECM blower has a moderate startup demand that most 2,000W+ power stations can handle. | |||||
| Goodman GMH8 0805B (80,000 BTU) | 810W | 2,430W | Soft Start | ~0.7h | NEC Standard |
Show expert analysisTechnical: **Running load:** 810W (derived from OEM Min Circuit Ampacity 8.8A de-rated by NEC 1.25× factor). **Surge:** 2,430W (3× running per NEC for PSC induction motor — OEM LRA not published). **Voltage:** 120V AC. The 4-speed PSC motor creates a hard mechanical inrush on every startup — three times the running load. Field note: The Goodman GMH8 represents millions of builder-grade furnaces installed across the US. The PSC motor surge is the critical factor — running watts are actually lower than ECM models, but the 2,430W startup spike will trip any power station under 2,500W. This is the #1 reason furnace blowers fail on small generators. Why does my power station shut off when the Goodman furnace blower starts? Because the PSC blower motor creates a 2,430W startup surge — 3× its 810W running draw. Most power stations under 2,500W surge capacity will trip on this inrush. You need a station rated for at least 2,430W surge to handle it reliably. | |||||
How This Pairing Performs Across Our Database
This unit is outside the compatible set; 22 of 33 generators pass SAFE/TIGHT for this device.
How Gas Furnace Fan (Blower) Performs Across 33 Tested Generators
22 of 33 generators are SAFE+TIGHT for Gas Furnace Fan (Blower).
22
Safe+Tight
Safe 20 (61%)
Tight 2 (6%)
Soft Start 1 (3%)
Fail 10 (30%)
Power Comparison: Anker SOLIX C800 Plus vs Top Alternatives for Gas Furnace Fan (Blower)
Anker SOLIX C800 Plus Fail
Current unit
Running 1,200W
Surge 1,600W
Fit class uses buffered needs (running and surge) for this device.
Specs & Surge Analysis
Heating & Cooling
Gas Furnace Fan (Blower)
Winter Heating Emergency
Select Your Model:
1058W
Running
2430W
Surge
120V
Required
True Surge™ Analysis
Safety Buffer: +15% Running Power Usage 78% to 101% Utilization
932W to 1217W required 1200W Capacity
Up to 268W headroom on lighter models; 17W short on demanding models
Surge/Startup Peak 105% to 175% Utilization
1681W to 2795W required 1600W Capacity
81W to 1195W short by model
Voltage Match 120V ↔ 120V ✓
Startup Surge Visual
Startup Surge
Gas Furnace Fan (Blower) vs SOLIX C800 Plus
Startup surge exceeds the power station limit. A soft starter may resolve the surge gap.
⚠️
Before You Buy: Connection Check
Installation warning
These systems are often hardwired to a home panel. To run them from a portable station, you may need a transfer switch installed by an electrician. You cannot just plug it in.
Compare Similar Units
Free Tools
Station Tools
Generator Insights
The 1600W surge rating can support startup sequences for refrigerator compressors, well pumps, and similar inductive motor loads that draw 25 to 33 percent over running current during initial engagement. Once running, the 1200W continuous output can handle typical kitchen appliances, electronics, and power tools within rated limits. This combination addresses both inrush events and sustained runtime needs in backup scenarios.
This unit uses LFP chemistry, a battery architecture chosen for thermal stability in consumer power stations. The 768Wh capacity and 1200W continuous output allow sustained operation without thermal stress under typical residential loads. Source: Anker SOLIX C800 Plus Tech Specs (manufacturer documentation).
Extend Runtime with Solar
Keep your Gas Furnace Fan (Blower) running with solar • MPPT: 11– 60V • Max: 300W
Official Anker
100W Panel
1 Hour Sun =
+0.1h per sun hour
MC4 -> XT60
Full in ~11h Adapter required: MC4 -> XT60.
Smart Value Bluetti
200W Panel
1 Hour Sun =
+0.1h per sun hour
MC4 -> XT60
Full in ~5.5h Adapter required: MC4 -> XT60.
Smart Value BougeRV
200W Panel
1 Hour Sun =
+0.1h per sun hour
MC4 -> XT60
Full in ~5.5h Adapter required: MC4 -> XT60.
Technical Analysis
Spec-Based • No GuaranteesTechnical Breakdown
Running load: 810–1,058W depending on motor type (ECM vs PSC). Surge: 1,461–2,430W. Voltage: 120V AC required. The motor technology — ECM variable speed, ECM constant torque, or PSC multi-speed — determines both the running draw and the startup surge that your power station must handle.
Expected Behavior
Estimated runtime: ~0.5h. Gas furnace blowers run 8+ hours per day during winter emergencies. ECM motors (Carrier, Trane) have controlled electronic startup. PSC motors (Goodman) create hard mechanical inrush at 3× running watts on every heating cycle. Daily energy ranges from 6,480–8,464 Wh.
Field Note
The blower motor is the only significant electrical load in a gas furnace — the gas burner itself uses negligible electricity. Check your furnace nameplate for motor type: ECM or constant torque means manageable surge; PSC or multi-speed means you need a power station rated for at least 2,500W surge.
Frequently Asked Questions
Can the Anker SOLIX C800 Plus power a Gas Furnace Fan (Blower)?
It depends on the model. 2 of 3 Gas Furnace Fan (Blower) models are compatible with the Anker SOLIX C800 Plus. See the model-specific results table for exact verdicts per model.
How long will the SOLIX C800 Plus run a Gas Furnace Fan (Blower)?
It depends on the model. Compatible models run approximately 0.5–0.7 hours on the SOLIX C800 Plus. 0 of 3 models are not compatible. See the model-specific results for details.
Power Tip: To get the most out of your SOLIX C800 Plus, keep it in a well-ventilated area. Extreme temperatures can slightly reduce the efficiency of the LFP/NMC cells.
Compare all 33 generators for the Gas Furnace Fan (Blower)
Ranked by budget, runtime, and overall compatibility.
Technical Sourcing & Verification
ID: anker-solix-c800-plus-gas-furnace-blower 🏛️ Device Data Source
Engineering Est. Safety Factor Applied
Derived from variant list (max of variants). Worst case running = Trane S8X1 B080 (1058W). Worst case surge = Goodman GMH8 080 (2430W). Running and surge maxima come from different variants due to ECM vs PSC motor technology.
⚡ Generator Specs Source
OEM Verified
Anker SOLIX C800 Plus User Manual (EN-US)
Methodology informed by US Department of Energy (DOE) & EIA references where applicable.
Our methodology →
Compare these models
Similar-output alternatives you can compare side by side.