1
Voltage Gate
PASSDevice output type must match generator output.
120V required -> 120V available
Can the AC200L Run a Shop Vac? It Depends on Your Model
1 of 3 models are compatible with this generator.
Jump to model-specific results ↓Power Margin Analysis
2400W / 3600W Capacity Running 799W to 1020W headroom by model
1380W to 1601W required
Surge 540W to 1203W short by model
4140W to 4803W required
Decision Gate Waterfall
Same decision gates as the engine: voltage, running, surge. Runtime is shown as operational context.
2
Running Gate
PASSContinuous draw with safety buffer applied.
1,380W to 1,601W required -> 2,400W available (799W to 1,020W headroom)
Required 1,380W to 1,601W required
Available 2,400W
3
Surge Gate
FAILStartup peak with safety buffer applied.
4,140W to 4,803W required -> 3,600W available (540W to 1,203W short)
Required 4,140W to 4,803W required
Available 3,600W
4
Runtime Insight
INFORuntime context only. It does not change the electrical compatibility verdict.
Continuous estimate: 1.0h
Device profile reference: up to 1h per day.
Power bars show required versus available output for each gate.
View full compatibility reportDecision Snapshot
Quick compatibility, required headroom, and model-specific context at a glance.
⚡
2400W
Running Power
🔋
2048Wh
Capacity
⏱️
~1h
Est. Runtime
☀️
1200W
Solar Input
Quick Compatibility Check
- 1 1 of 3 models are compatible with the AC200L.
- 2 Model requirements range from 1200W to 1392W running watts.
- 3 See the model-specific results table for per-model verdicts.
Model-Specific Results
1 of 3 models are SAFE or TIGHT. Most demanding model: Shop-Vac SVX2 (12-Gal, 5.5 HP Peak) (4,176W surge).
| Model | Running | Surge | Verdict | Runtime | Source |
|---|---|---|---|---|---|
| DeWalt DXV10P (10-Gal, 5.5 HP, 2-Stage Quiet) | 1,200W | 3,600W | Tight | ~1.2h | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1200W from OEM nameplate (10A × 120V). **Estimated startup surge:** 3600W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. 2-stage motor, 90 CFM airflow, 73 dB noise rating — quietest in this set. Field note: The DXV10P is the most power-station-friendly shop vac in this set. At 1200W running and an estimated 3600W surge, it works with most power stations rated 2000W+ with adequate surge capacity. The 2-stage motor runs quieter (73 dB) and may have lower actual inrush than single-stage models, though no OEM data confirms this. Can a portable power station run the DeWalt DXV10P? Only if your power source can supply at least 1200W continuous and approximately 3600W surge at 120V. The motor startup surge is the main challenge, not the running watts. | |||||
| Vacmaster Beast VFB511B (5-Gal, 6 HP Peak, Compact) | 1,320W | 3,960W | Fail | — | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1320W from OEM specs (11A × 120V). **Estimated startup surge:** 3960W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. Single-stage motor, 102 CFM airflow, 320 Air Watts, 82 in. water lift. Field note: The Beast packs the most suction power per pound in this set — 102 CFM from a 12 lb unit. At 1320W running it draws 10% more than the DeWalt but delivers 13% more airflow. The compact 5-gallon tank makes it portable but limits continuous use on large jobs. Is the Vacmaster Beast harder to run on a power station than the DeWalt? Slightly — 1320W versus 1200W running, with an estimated 3960W versus 3600W surge. Both need a power station with at least 2000W continuous and 4000W+ surge for reliable startup. | |||||
| Shop-Vac SVX2 (12-Gal, 5.5 HP Peak) | 1,392W | 4,176W | Fail | — | Engineering Est. |
Show expert analysisTechnical: **Running load:** 1392W from OEM specs (11.6A × 120V). **Estimated startup surge:** 4176W at 3x running (motor-load multiplier — no OEM starting watts published). **Voltage:** 120V AC. SVX2 motor, 12-gallon tank — the highest-draw unit in this set. Field note: The SVX2 draws the most power in this set at 11.6A. Its estimated 4176W startup surge puts it beyond most mid-range power stations. If you need a shop vac specifically for portable power use, the 10A DeWalt is a safer choice. The SVX2 is best paired with stations rated 2500W+ continuous with 5000W surge. Why does the Shop-Vac draw more than the 6 HP Vacmaster? Peak HP is a marketing metric, not an electrical measurement. The SVX2 at 11.6A draws more real power than the 6 HP Beast at 11A. Always check nameplate amps, not HP ratings, for power station sizing. | |||||
How This Pairing Performs Across Our Database
This unit is outside the compatible set; 12 of 33 generators pass SAFE/TIGHT for this device.
How Shop Vac (Wet/Dry, 5-6 HP Peak) Performs Across 33 Tested Generators
12 of 33 generators are SAFE+TIGHT for Shop Vac (Wet/Dry, 5-6 HP Peak).
12
Safe+Tight
Safe 9 (27%)
Tight 3 (9%)
Fail 21 (64%)
Power Comparison: Bluetti AC200L vs Top Alternatives for Shop Vac (Wet/Dry, 5-6 HP Peak)
Bluetti AC200L Fail
Current unit
Running 2,400W
Surge 3,600W
Fit class uses buffered needs (running and surge) for this device.
Specs & Surge Analysis
Power Tools
Shop Vac (Wet/Dry, 5-6 HP Peak)
Workshop Cleanup
Select Your Model:
1392W
Running
4176W
Surge
120V
Required
True Surge™ Analysis
Safety Buffer: +15% Running Power Usage 57% to 67% Utilization
1380W to 1601W required 2400W Capacity
799W to 1020W headroom by model
Surge/Startup Peak 115% to 133% Utilization
4140W to 4803W required 3600W Capacity
540W to 1203W short by model
Voltage Match 120V ↔ 120V ✓
Startup Surge Visual
Startup Surge
Shop Vac (Wet/Dry, 5-6 HP Peak) vs AC200L
Startup surge exceeds the power station limit. A soft starter may resolve the surge gap.
Compare Similar Units
Free Tools
Station Tools
Generator Insights
The 3600W surge rating can support typical residential compressor-based loads during startup, including window AC units, refrigerators, and well pumps that demand brief high-current draws. With 2400W running capacity, the system can handle sustained operation of multiple mid-range appliances once inrush currents subside. This combination addresses both the initial power spike and continuous runtime for everyday backup scenarios.
This unit employs LFP chemistry, a cathode technology known for thermal stability in residential applications. The 2048Wh capacity and inverter output specs are drawn directly from the manufacturer's published materials. Source: BLUETTI AC200L User Manual (Specifications Section) (manufacturer documentation).
Extend Runtime with Solar
Keep your Shop Vac (Wet/Dry, 5-6 HP Peak) running with solar • MPPT: 12– 145V • Max: 1200W
Official Bluetti
350W Panel
1 Hour Sun =
+0.2h per sun hour
MC4 -> Proprietary
Full in ~8.4h Adapter required: MC4 -> Proprietary.
Smart Value Anker
400W Panel
1 Hour Sun =
+0.2h per sun hour
MC4 -> Proprietary
Full in ~7.3h Adapter required: MC4 -> Proprietary.
Smart Value EcoFlow
400W Panel
1 Hour Sun =
+0.2h per sun hour
MC4 -> Proprietary
Full in ~7.3h Adapter required: MC4 -> Proprietary.
Technical Analysis
Spec-Based • No GuaranteesTechnical Breakdown
Running range: 1200W (10A) to 1392W (11.6A) depending on motor size. Estimated surge range: 3600W to 4176W at 3x running (motor-load multiplier — no shop vac manufacturer publishes starting watts). Voltage: 120V AC for all residential models.
Expected Behavior
Estimated runtime: ~1h. Shop vacs draw near-maximum rated power continuously while running. Unlike power tools that cycle between cuts, a shop vac runs steady until you release the trigger or switch. At 1 hour daily use, energy consumption ranges from 1200 to 1392 Wh.
Field Note
Peak HP is meaningless for power station sizing — a '6 HP' vac may draw less amps than a '5.5 HP' model. Always check the nameplate amperage. Motor startup surge is the primary compatibility concern: a shop vac that draws 1200W running may need 3600W briefly at startup. Size for surge capacity first.
Frequently Asked Questions
Can the Bluetti AC200L power a Shop Vac?
It depends on the model. 1 of 3 Shop Vac (Wet/Dry, 5-6 HP Peak) models are compatible with the Bluetti AC200L. See the model-specific results table for exact verdicts per model.
How long will the AC200L run a Shop Vac?
It depends on the model. Compatible models run approximately 1.2–1.2 hours on the AC200L. 2 of 3 models are not compatible. See the model-specific results for details.
What Else Can You Run?
With 335W allocated to the Shop Vac (Wet/Dry, 5-6 HP Peak), the AC200L still has ~193W of margin. These devices could run simultaneously:
🌀
Box Fan (Medium)
60W
💡
LED Lamp
10W
📺
55' LED TV
80W
❄️
Medical Fridge
80W
💻
MacBook Air/Pro
65W
🩺
CPAP (No Humidifier)
40W
Power Tip: To get the most out of your AC200L, keep it in a well-ventilated area. Extreme temperatures can slightly reduce the efficiency of the LFP/NMC cells.
Compare all 33 generators for the Shop Vac (Wet/Dry, 5-6 HP Peak)
Ranked by budget, runtime, and overall compatibility.
Technical Sourcing & Verification
ID: bluetti-ac200l-shop-vac-5hp 🏛️ Device Data Source
Engineering Est. Safety Factor Applied
Derived from variant list (max of variants). Running worst case = Shop-Vac SVX2 (1392W at 11.6A). Surge worst case = Shop-Vac SVX2 (4176W). Surge estimated using 3x motor-load multiplier policy (no OEM starting watts published for any shop vac in this class).
⚡ Generator Specs Source
OEM Verified
BLUETTI AC200L - Official Product Page
Methodology informed by US Department of Energy (DOE) & EIA references where applicable.
Our methodology →
Compare these models
Similar-output alternatives you can compare side by side.